{"product_id":"massey-ferguson-5710-sl-5711-sl-5712-sl-5713-sl-tractor-service-manual-workshop-guide","title":"Massey Ferguson 5710 SL, 5711 SL, 5712 SL, 5713 SL Tractor Service Manual Workshop Guide","description":"Format : PDF\u003cbr\u003eSUPPLIED AS DOWNLOADABLE LINK\u003cbr\u003e\u003cbr\u003eMassey Ferguson 5710 SL, 5711 SL, 5712 SL, 5713 SL Tractors Workshop Manual – 1366 Pages\u003cbr\u003eSpicer Axle 730\/563 Service Manual – 74 Pages\u003cbr\u003eTechnician Service Book MF 5700 SL -456 Pages\u003cbr\u003eParts Catalog (Dyna 4 \u0026amp; Dyna 6) – 532 Pages \u0026amp; 518 Pages\u003cbr\u003eFormat: PDF\u003cbr\u003eLanguage: English\u003cbr\u003ePublication No: ACT0021460\u003cbr\u003e\u003cbr\u003eDescription\u003cbr\u003eMassey Ferguson 5710 SL, 5711 SL, 5712 SL, 5713 SL Tractor Manual\u003cbr\u003eModel:\u003cbr\u003eMassey Ferguson\u003cbr\u003eMF 5700SL Series Tractor\u003cbr\u003eFormat: PDF\u003cbr\u003eLanguage: English\u003cbr\u003ePublication No: ACT0021460\u003cbr\u003eMassey Ferguson 5710 SL, 5711 SL, 5712 SL, 5713 SL Tractors Workshop Manual – 1366 Pages\u003cbr\u003eSpicer Axle 730\/563 Service Manual – 74 Pages\u003cbr\u003eTechnician Service Book MF 5700 SL -456 Pages\u003cbr\u003eParts Catalog (Dyna 4 \u0026amp; Dyna 6) – 532 Pages \u0026amp; 518 Pages\u003cbr\u003eManual Table of Content\u003cbr\u003e1 Introduction\u003cbr\u003e2 Separation of assemblies\u003cbr\u003e3 Engine\u003cbr\u003e4. Clutch\u003cbr\u003e5. Gearbox\u003cbr\u003e6. Rear axle\u003cbr\u003e7. Power Take Off\u003cbr\u003e8. Front axle\u003cbr\u003e9. Hydraulics\u003cbr\u003e10. Electricity\u003cbr\u003e11. Electronics\u003cbr\u003e12 Cab\u003cbr\u003e13 Accessories\u003cbr\u003e14 Service tools\u003cbr\u003eGPA50\/Rear PTO with two electrohydraulic speeds\u003cbr\u003eGeneral\u003cbr\u003eThe unit fitted to the rear of the GPA50 rear axle contains all the mechanical components of the two speed rear PTO. These elements rest on tapered roller bearings for which certain cups are fitted \"tightened\" and others are \"free\" in the single-piece housing.\u003cbr\u003eThe two-speed rear PTO is independent of the transmission.\u003cbr\u003eChanging between the speeds (540 – 540E) of the two-speed PTO is managed hydraulically via the electronic system of the tractor.\u003cbr\u003eIn this section, only a partial description is given of each component, as more specific and detailed descriptions are given in their respective sections.\u003cbr\u003eThe two-speed rear PTO is divided into four parts: • The clutch The clutch is located on the upper power take-off shaftline and at the front of the center housing. The front part is fitted with a Gerotor type lubrication pump which lubricates the clutch and the gearbox. It is supported by two ball bearings fitted in a support mounted on the center housing.\u003cbr\u003e• The upper shaftline\u003cbr\u003eThe upper shaftline of the rear PTO transmits the engine speed to the drive gears of the rear PTO unit via the clutch and a line consisting of three shafts. The drive gears are housed in a single-piece housing.\u003cbr\u003eThe tapered roller bearings supporting the drive shaft and gears are shimmed with a preload using shim(s) inserted between the front bearing cup and the single-piece housing cover plate.\u003cbr\u003e• The lower shaftline\u003cbr\u003eThe rear PTO lower shaftline is supported by two tapered roller bearings mounted respectively in the single-piece housing\u003cbr\u003eThe bearings are held in position by a nut screwed to the front end of the output shaft. Shimming by preloading the tapered roller bearings is achieved using shims which are inserted between the front bearing cup and the single-piece housing.\u003cbr\u003eA lip seal fitted to the single-piece housing ensures the output shaft tightness.\u003cbr\u003eImproved sealing is provided for cases of prolonged use in damp environments such as paddy fields. A special seal is then fitted to the end of the output shaft.\u003cbr\u003eThe output shaft is fitted with an interchangeable end (E) which can have 6 or 21 splines.\u003cbr\u003eNOTE: The number of splines on the output shaft depends on the nature of the driven implement and the required rotation speed.","brand":"Uploader","offers":[{"title":"Default Title","offer_id":53593202131275,"sku":null,"price":63.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0978\/2519\/4315\/files\/1-60_0ed7a789-efe6-4fed-a6b0-a5fb309479fd.png?v=1760373122","url":"https:\/\/manualbull.com\/products\/massey-ferguson-5710-sl-5711-sl-5712-sl-5713-sl-tractor-service-manual-workshop-guide","provider":"ManualBull","version":"1.0","type":"link"}