{"product_id":"hino-truck-2014-conventional-service-manual-workshop-guide","title":"Hino Truck 2014 Conventional Service Manual Workshop Guide","description":"Format : PDF\u003cbr\u003eSUPPLIED AS DOWNLOADABLE LINK\u003cbr\u003e\u003cbr\u003eFormat: PDF\u003cbr\u003eLanguage: English\u003cbr\u003eHino 2014 Conventional Truck Manual for 238, 258LP, 268, 338 Series – 1009 Pages\u003cbr\u003eHino 2014 Conventional Owners Manual – 446 Pages\u003cbr\u003eTroubleshooting Hino 2014 Manual – 919 Pages\u003cbr\u003eHino J08E-VB and J08E-VC Engine Manual – 339 Pages\u003cbr\u003e\u003cbr\u003eDescription\u003cbr\u003eHino Truck 2014 Conventional Service Manual\u003cbr\u003eThis is the Repair and Service Manual for\u003cbr\u003eHino Truck\u003cbr\u003e2014\u003cbr\u003eApplicable for 238, 258LP, 268, 338 Series –\u003cbr\u003eFormat: PDF\u003cbr\u003eLanguage: English\u003cbr\u003eHino 2014 Conventional Truck Manual for 238, 258LP, 268, 338 Series – 1009 Pages\u003cbr\u003eHino 2014 Conventional Owners Manual – 446 Pages\u003cbr\u003eTroubleshooting Hino 2014 Manual – 919 Pages\u003cbr\u003eHino J08E-VB and J08E-VC Engine Manual – 339 Pages\u003cbr\u003eThis workshop manual has been prepared to provide information covering repairs on 238, 258LP, 268, 338 Series Hino 2014 Conventional trucks.\u003cbr\u003eTo use Hino 2014 Conventional trucks for years, smoothly, safely, and economically without trouble, it is important to perform inspections.\u003cbr\u003eMaintenance required to be performed is the responsibility of the owner. Some recommended repairs of your truck are mentioned. When making any repair of your truck, be careful not to be injured through improper procedures.\u003cbr\u003eAs for maintenance items, refer to the Owners and Drivers Manual. All information and specifications in this manual are based upon the latest product information available at the time of printing.\u003cbr\u003eTable of Content For Hino 2014 Conventional Truck Manual:\u003cbr\u003eGeneral Introduction\u003cbr\u003eClutch Equipment\u003cbr\u003eClutch Main Unit\u003cbr\u003eClutch Control\u003cbr\u003eTransmission Equipment\u003cbr\u003eTransmission Main Unit\u003cbr\u003eTransfer Main Unit\u003cbr\u003eAutomatic Transmission\u003cbr\u003eP.t.o. (Power Take-off)\u003cbr\u003eTransmission \/ Transfer Control\u003cbr\u003ePropeller Shaft\u003cbr\u003eDifferential Equipment\u003cbr\u003eDifferential Carrier\u003cbr\u003eIndex: Chassis Group 1\/4\u003cbr\u003ePropeller Shaft Equipment\u003cbr\u003eBrake Equipment\u003cbr\u003eService Brake\u003cbr\u003eAbs \u0026amp; Asr\u003cbr\u003eEs Start (Easy \u0026amp; Smooth Start) System\u003cbr\u003eExhaust Brake\u003cbr\u003eRetarder Brake\u003cbr\u003eParking Brake\u003cbr\u003eSteering Equipment\u003cbr\u003eSteering Unit\u003cbr\u003ePower Steering\u003cbr\u003eAxle Equipment\u003cbr\u003eFront Axle\u003cbr\u003eRear Axle\u003cbr\u003eWheel \u0026amp; Tire\u003cbr\u003eSuspension Equipment\u003cbr\u003eSuspension\u003cbr\u003eChassis Equipment\u003cbr\u003eChassis Frame\u003cbr\u003eCoupler (5th Wheel)\u003cbr\u003ePintle Hook\u003cbr\u003eHino Truck 2014 Conventional Manual Instruction Extract:\u003cbr\u003eTORQUE VALUES FOR FASTENERS\u003cbr\u003e1. GENERAL INFORMATION\u003cbr\u003e(1) The torque values on page DF02-1112 are for fasteners that have a light application of oil on the threads.\u003cbr\u003e• If the fasteners are dry: Increase the torque values by 10%.\u003cbr\u003e• If the fasteners have a heavy application of oil on the threads: Decrease the torque values by 10%.\u003cbr\u003e(2) If you do not know the size of the fastener that is being installed, measure the fastener. Use the following procedure.\u003cbr\u003e2. AMERICAN STANDARD FASTENERS\u003cbr\u003e. a. Measure the diameter of the threads in inches, dimension X.\u003cbr\u003eb. Count the amount of threads in 1-inch.\u003cbr\u003eExample\u003cbr\u003e• American Standard size fastener is 0.50-13.\u003cbr\u003e• 0.50 is the diameter of the fastener in inches or dimension X.\u003cbr\u003e• 13 is the amount of threads in 1-inch.\u003cbr\u003e3. METRIC FASTENERS\u003cbr\u003e. a. Measure the diameter of the threads in millimeters (mm), dimension X.\u003cbr\u003eb. Measure the distance of 10 threads, point to point in millimeters (mm), dimension Y. Make a note of dimension Y.\u003cbr\u003ec. Divide dimension Y by 10. The result will be the distance between two threads or pitch.\u003cbr\u003eExample\u003cbr\u003e• Metric size fastener is M8 x 1.25. M8 is the diameter of the fastener in millimeters (mm) or dimension X.\u003cbr\u003e• 1.25 is the distance between two threads or pitch.\u003cbr\u003e(1) Compare the size of fastener measured in 1. (2) above to the list of fasteners on page DF02-1112 to find the correct torque value.","brand":"Uploader","offers":[{"title":"Default Title","offer_id":53593324749131,"sku":null,"price":61.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0978\/2519\/4315\/files\/1-11_751ebfa8-83bd-4f79-aa4e-30db93b71992.png?v=1760374811","url":"https:\/\/manualbull.com\/products\/hino-truck-2014-conventional-service-manual-workshop-guide","provider":"ManualBull","version":"1.0","type":"link"}