{"product_id":"case-521g-loader-service-manual-workshop-guide","title":"Case 521G Loader Service Manual Workshop Guide","description":"Format : PDF\u003cbr\u003eSUPPLIED AS DOWNLOADABLE LINK\u003cbr\u003e\u003cbr\u003eManual Included:\u003cbr\u003e•\u003cbr\u003eService Manual:\u003cbr\u003e2829 pages \u0026amp; 2831 pages (Tier 4B) and 2087 pages (Tier 2)\u003cbr\u003eSpecifications:\u003cbr\u003e•\u003cbr\u003eBrand:\u003cbr\u003eCase\u003cbr\u003e•\u003cbr\u003eModel:\u003cbr\u003e521G\u003cbr\u003e•\u003cbr\u003eType:\u003cbr\u003eLoader\u003cbr\u003e•\u003cbr\u003eManuals:\u003cbr\u003eService Manual\u003cbr\u003e•\u003cbr\u003ePublication Numbers:\u003cbr\u003e51428262 (Dec 2017), 48083739 (Jul 2018) and 51428203 (Nov 2017)\u003cbr\u003e•\u003cbr\u003eLanguage:\u003cbr\u003eEnglish\u003cbr\u003e•\u003cbr\u003eFormat:\u003cbr\u003ePDF\u003cbr\u003e\u003cbr\u003eDescription\u003cbr\u003eTable of Contents\u003cbr\u003eContent\u003cbr\u003eIntroduction\u003cbr\u003eEngine\u003cbr\u003eTransmission\u003cbr\u003eFour Wheel Drive System\u003cbr\u003eFront Axle\u003cbr\u003eRear Axle\u003cbr\u003eBrakes and Controls\u003cbr\u003eHydraulic System\u003cbr\u003eFrames and ballasting\u003cbr\u003eSteering\u003cbr\u003eWheels\u003cbr\u003eCab climate control\u003cbr\u003eElectrical System\u003cbr\u003eFront Loader and Bucket\u003cbr\u003ePlatform, Cab, Bodywork and Decals\u003cbr\u003eSpecial Tool Index\u003cbr\u003eElectrical Schematics\u003cbr\u003eManual Extract: Hydraulic service brakes – Bleed – Bleeding the Brake System\u003cbr\u003e1. Check the level of the hydraulic fluid in the reservoir.\u003cbr\u003eAdd fluid to the reservoir if necessary.\u003cbr\u003eNOTE: if the machine is equipped with quick-attached components, disconnect them from machine prior to proceeding.\u003cbr\u003e2. Raise the loader arms and install the safety link.\u003cbr\u003e3. Put the articulation lock in the LOCKED position.\u003cbr\u003e4. Apply the parking brake.\u003cbr\u003e5. To prime the pump, do the following:\u003cbr\u003eA. Turn the ignition switch to the OFF position.\u003cbr\u003eB. Turn the timed disconnect switch to the OFF position.\u003cbr\u003e6. Disconnect the connectors from the ECU to prevent the start of the engine.\u003cbr\u003e7. Loosen the fitting on the brake pump section hose 9. Turn the ignition switch to ON and crank the engine (the engine will not start).\u003cbr\u003e10. Do the following:\u003cbr\u003eA. Turn the ignition switch to ON. and crank the engine (the engine will not start).\u003cbr\u003eB. Crank the engine (the engine will not start) until a few drops of oil leak past the fitting.\u003cbr\u003eC. After a few drops of oil are noticed, tighten the fitting.\u003cbr\u003e11. Turn the timed disconnect switch to the OFF position.\u003cbr\u003e12. Connect the connectors on the ECU.\u003cbr\u003e13. Turn the timed disconnect switch to the ON position.\u003cbr\u003e14. Start the engine. Idle until both brake accumulators are fully charged.\u003cbr\u003eNOTE: after approximately 30 s the low brake pressure indicator light will not be illuminated.\u003cbr\u003e15. Turn the ignition switch to the OFF position.\u003cbr\u003e16. Push the brake pedal to relieve the hydraulic pressure in the brake system (approximately 20 times).\u003cbr\u003e17. Remove the plastic and rubber cap from each wheel.\u003cbr\u003eSlowly open the bleed screws.\u003cbr\u003e18. Attach a hose to the bleed screws to prevent spillage.\u003cbr\u003eSubmerge the hoses in fluid to prevent that air enters to the brake system.\u003cbr\u003e19. Turn the ignition switch to the ON position. Start the engine and run at low idle for few minutes.\u003cbr\u003e20. Depress the brake pedal until the flow is clear with no air bubbles present in both tubes.\u003cbr\u003e21. Close all four wheel end bleed screws.\u003cbr\u003e22. Replace all of the caps and plugs on the wheel end.\u003cbr\u003e23. Check and verify that the hydraulic fluid level is filled to specification. Fill as required.","brand":"Uploader","offers":[{"title":"Default Title","offer_id":53600948486475,"sku":null,"price":63.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0978\/2519\/4315\/files\/1-86_96afd8d1-7609-4511-b709-292d3576643c.png?v=1760438254","url":"https:\/\/manualbull.com\/products\/case-521g-loader-service-manual-workshop-guide","provider":"ManualBull","version":"1.0","type":"link"}