{"product_id":"agco-gt45-gt55-gt65-gt75-tractor-workshop-service-manual-workshop-guide","title":"AGCO GT45, GT55, GT65, GT75 Tractor Workshop Service Manual Workshop Guide","description":"Format : PDF\u003cbr\u003eSUPPLIED AS DOWNLOADABLE LINK\u003cbr\u003e\u003cbr\u003eManual for:\u003cbr\u003eAGCO\u003cbr\u003eDTA Tractor\u003cbr\u003eFormat: PDF\u003cbr\u003eBook Number: 79021715\u003cbr\u003eEnglish\u003cbr\u003eAGCO GT45, GT55, GT65, GT75 Tractor Manual : 363 Pages\u003cbr\u003e\u003cbr\u003eDescription\u003cbr\u003eAGCO GT45, GT55, GT65, GT75 Tractor Manual\u003cbr\u003eManual for:\u003cbr\u003eAGCO\u003cbr\u003eGT Tractor\u003cbr\u003eFormat: PDF\u003cbr\u003eBook Number: 79021715\u003cbr\u003eEnglish\u003cbr\u003eAGCO GT45, GT55, GT65, GT75 Tractor Manual : 363 Pages\u003cbr\u003eManual TABLE OF CONTENTS\u003cbr\u003eGeneral Information\u003cbr\u003eEngine\u003cbr\u003eTransmission\u003cbr\u003eDrive Axles\u003cbr\u003eBrakes\u003cbr\u003eHydraulics\u003cbr\u003eControls\u003cbr\u003eBody\u003cbr\u003eSystem\u003cbr\u003eElectrical System\u003cbr\u003eGT45, GT55, GT65, GT75 Manual Extract\u003cbr\u003eCleaning crankshaft and cylinder block internal passages\u003cbr\u003eCleaning of the lubricating oil passage should be made after all crankshaft and cylinder block overhauling operations have been accomplished. This cleaning can be carried out by using Diesel fuel or compressed air blasted into the passages Checking crankshaft end play.\u003cbr\u003eThis check is performed with a magnetic base comparator operating as follows:\u003cbr\u003e— place the magnetic base together with the comparator onto the crankcase and then make the comparator feeler contact one of the crankshaft ends.\u003cbr\u003e— use a lever to move the crankshaft axially towards the comparator side until the comparator hand stops moving.\u003cbr\u003e— reset the comparator and push the crankshaft with the lever towards the opposite side and then take the end play reading from the comparator dial.\u003cbr\u003eThis reading should be 0.004-0.010\" (0,10 to 0,27 mm); if higher than specified, some spacing half-rings with 0.004-0.008\" (0,10 to 0,20 mm) oversize with respect to the nominal thickness shall be fitted. These half-rings are regularly supplied as spare parts.","brand":"Uploader","offers":[{"title":"Default Title","offer_id":53593089704267,"sku":null,"price":52.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0978\/2519\/4315\/files\/1-19_050c4820-daa1-445f-9579-a5e5c56d9dbe.png?v=1760372312","url":"https:\/\/manualbull.com\/products\/agco-gt45-gt55-gt65-gt75-tractor-workshop-service-manual-workshop-guide","provider":"ManualBull","version":"1.0","type":"link"}